Assist with electrical testing during start-ups. Basic knowledge of electrical equipment protection
systems and recording instruments. LTE, UMTS, GSM, CDMA components, photograph and
document, SWEEP/PIM testing and fiber testing, azimuth, ret settings, antenna alignment.
AT&T, T-Mobile, Verizon, Sprint 2.5 install and US Cellular decom.

SKILL TO:
Assist design engineers and project managers, review design drawings, read and interpret
electrical schematics, logic, elementary, wiring and control diagrams, troubleshoot electrical and
control circuits to locate problems, electrical testing and provide necessary repairs .Assist
engineer with differentials testing. Experience in electric utility substation integration,
automation, and protection system upgrades, design, documentation, installation and testing.
Lead electrical install and civil construction crews.

INSTALLATIONS:
Build and work inside distribution 69kv, 230kv and 500kv switchyard substation, remove and
install new relay and control panels, remove OCB and install new GCB, remove and install
new relays, line current differential protection and automation systems. Install AC/DC
distribution panels, transformers, RTU’s, reactors, insulators, line bus, control, and equipment
grounds. Wiring and testing of new SCADA system. Electro –mechanical relays with
microprocessor based relays in existing substation. DAS/Central office or cell site installs.
Replacement of BTS equipment, site support cabinets ,COVP, emergency and normal power
panels, batteries, rectifiers, RRH radios, antennas, coax, fiber, jumpers, connectors, -48v and
+24v power plants and convertors. Telecommunications routers and Ethernet, T1’s and
alarms. .

TROUBLESHOOTING AND REPAIR:
Assist higher classified employees with testing of control and relay circuits, line current and
potential circuits, auxiliary control circuits, data and fault recorders to find, identify and correct
problems. Repair electro mechanical relays and wiring problems. Test and document during
start-up. AT&T, T-Mobile, Verizon, Sprint 2.5 wireless communication systems. Check
differentials using Doble (F-6150) test equipment 60amp to 100amp.

SAFETY:
Use safe work practices, methods and procedures to work on or around high voltage ( up to
230kv and 500kv ) and low voltage ( 600 volt or less ) systems. Comply with with NERC and
FERC standards and requirements

TECHNICAL KNOWLEDGE AND ACCOMPLISHMENTS:
 Remove and install new relays, line current protection and automation systems
Experienced Nokia equipment training and equipment install
Install Nokia Flexi L700/ L1900 modules, MPR radios, batteries, Nokia / Ericsson /
Alcatel 8000&9500, C&I training (have to retrieve my PT #)
 Modify and terminate SCADA systems, RTU’s, DFR’s, PLC’s ,CT’s PT’s.
Terminate SEL-311, F60, B90, C30 relays, stuck breaker panels, gas circuit breakers,
protective relay control wiring, lockout relays, local-remote switches, low gas relays,
alarms, RTU programs, potential currents, contact input and output, testing,monitoring,
and metering
Familiar with FSMF, ESMB, GSM , LTE,TMA’s, Integrating and commissioning
Knowledge of electrical schematics , elementary, diagram and control drawings
 Fiber optic port connectivity and RJ45 and 66 block terminations
 Perform maintenance, inspect and test electrical equipment
WORK EXPERIENCE:

2014 – 2015
SACWireless, Schuamburg , Illinois
Civil Electrician – AT&T, T-Mobile, Verizon, Sprint 2.5, US Cellular builds and upgrades. Install
site configurations L700 with L1900. Assist with cutovers, T1 and Ethernet connections, RJ45
connections, RF jumper connections, remove and install routers, AC/DC power connections,
Nokia training, install diplexers, TMA’s, Nokia Flexi modules and radios, alarms, etc.

2014
TowerComm, Raleigh, NC
Civil Electrician – T-Mobile modernization TMO site configurations complete build, grounding,
concrete pad, grids, cabinet installs, AC/DC power, rigid and flex conduit install, -48 +24
terminations, COVP installs, RF equipment, power distribution panels, teleco box , fiber and
LMU cable, 25amp to 100amp circuit breakers, alarms, GPS and antenna mounting, etc.

2013
Baran Telecom, Alpharetta, GA
Civil Electrician – AT&T modernization, Install emergency and normal power panels, battery
testing, DC audits, preventive maintenance, install routers, Ethernet, cable trays, power
transmission and distribution panels, +24 -48 power plants, generators, circuit breakers,
decommission of telecommunications and power distribution equipment, AT&T on-site shelter
installs of telecommunications equipment.

2013
Overland Contracting, Conyers, GA
Civil Electrician – T-Mobile modernization, LTE upgrades, installation and testing, etc. Install
site support cabinets, power and Cat6 cable install, fiber install, assist with integration and
commission during cutover, RF connections, RJ45 connections, install routers. Central office,
DAS and cell sites installation of telecommunications equipment, DC power, wire wrapping,
equipment racks, color codes, batteries and power plants. AT&T standards and procedures.

2012 – 2013
Utility Lines Construction, Millersville, MD
Dominion Power Company, Alexandria, VA / BG&E, Baltimore, MD / PEPCO,
Washington. DC

Journeyman Substation Technician – worked in high voltage 230kv and 500kv switchyard
substation and control house as a relay and control wiring technician. Assist in testing,
installation, maintenance and repair of electrical equipment used to protect, operate and control
generation, transmission and distribution systems. Assist in the inspection, test, calibration, and
repair of electro-mechanical, relays, controls and equipment. Assist in assembling test
equipment and completes forms of test results, cleans and maintains equipment.

2011 – 2012
C.W. Wright Construction, Richmond, VA
Potomac Electric Power Co. (PEPCO) Washington, DC
Industrial/Commercial Electrician – Worked in high voltage 69kv/ 230kv/ 500kv switchyard
substation and control house as a relay and control wiring technician. Assisting higher
classified employees with inspection, installation, testing and repair. Terminate electrical
connections throughout electrical equipment protection system and recording instruments.

2009 – 2010
Super-Structure, Portsmouth, VA
MHI Shipyard, Norfolk, VA
Marine Electrician – Worked on Military Navy DDG Vessel upgrading weapons systems,
disconnect and relocate electrical equipment, install and hook-up temporary power, etc.

2009
NSC Technologies, Portsmouth, VA
BAE Systems Shipyard, San Diego, CA
Marine Electrician – Worked on Military Navy MSC Supply Vessel installing IDS security
systems and mounting new FDPP panels, pull cables, etc.

2008 – 2009
Worldwide Labor Support, Pascagoula, MS
BAE Systems- Puget Sound Navy Shipyard
Marine Electrician – Worked on Military Navy Aircraft Carrier communication and control
systems, ripping out and installing new equipment.

2007 – 2008
C. W. Wright Construction Co., Richmond, VA
Industrial Electrician – Build high voltage sub-stations and install new equipment

2005 – 2007
Shaw Constructors, Richmond, VA
Dominion Power, Chesterfield, VA
Industrial Electrician –Install new breakers, generators, motors, transformers and switchgears

EDUCATION:
Certificate – Electrical/Electronic Technology 2005
Halifax Community College, Roanoke Rapids, NC