WORK EXPERIENCE

Certified Pipe Welder
TRADE MANAGEMENT INC – Plano, TX – June 2016 to Present
working with city wide mechanical I installed chill water system using carbon steel black pipe.Welding pipe
from 4″ to 12″ pipe in all positions. Here in Texas we installed for a high riser downtown 38 story tall also using
6010 and 7018 rods. Also had to fit and fabricate the pipe.

Structural Welder
Henry builders construction – Lancaster, TX – April 2015 to May 2016
Skills Used
Demostrate my welding and fitting skills structual there I help build a 6 story office building. Skills range from
installing stairways and putting steel in the inbeds all around the building also installing galvanized angle 5×5
in the windows. There we also installed I beams and steel tubing for the elevator shafts.

pipe welder certified
Trade Mngt/City wide mech – Plano, TX – December 2014 to April 2015
We ran sched 4 inch all the way to sched 10 inch pipping from 1st floor to the sixth floor to also tie into the
cooling towers on the roof. At every floor we tie into the air handlers with our pipping whether using nipples or
reducers and 90’s to make the fit we also put in open and close valve and as well as flanges i use 6010 and
7018 in my welding procedure. I also did another job before the frisco job with City Wide in Sulfur Spring Tx i
help fitt a lot of the pipping and underground pipping for charles processer.

Millwright
Contractors Resource Inc. – Duncanville, TX – May 2014 to December 2014
Responsibilities
Build conveyors lines for UPS . I frabricated parts that needed to be on the line to run accordingly . Fitted any
parts that needed to be fitted also cut degrees and angles to make turns on the conveyor belt.I am a certified
welder a_w s d 1.1code I also weld all of the structural post making the conveyor line.

Skills Used
Frabrication,welding,fitting to get the job done.

Certified Pipe Welder
TRADE MANAGEMENT INC/ TDI Mech – Plano, TX – February 2014 to May 2014
Responsibilities
I weld and fitted carbon steel pipe for the the chill water system put in risers 18 story tall for state farm building.
I also help put in the pump room. Whether it takes using rust about or crane I help put it in I use 6010 and
7018 with welding procedures.

Skills Used
I use my welding skills of going on 12 yrs.

First Class Welder
World Wide Labor of Pascagula Mississippi – 2013 to 2014
there I repaired on oil rigs and ships and having to work in very tight spaces and also confine space to weld. I
maintain certification on FCAW, SMAW and also endure extreme tempertures and arc gouging.

Certified DW1.1 Welder
SHUECK STEEL STRUCTURAL MAINTENANCE \Nucor Steel – Blytheville, AR – 2013 to 2013
I perform Maintenance on the yard at Nucor Steel Mill.Whether it’s repairing on the big melting pot lid. Or
working 100 ft in the air in a man-lift welding in joist.Anything on the yard needed repairing steel or metal i
was called.

FCAW,SMAW,GMAW / Stainless Welder
TRADE FORCE of Colorado I – 2012 to 2013
Work for new companies and installed furnaces new. The washers are stainless steel as a welder we use
308 whether it was wire or stick it just depends. On the furnaces we use some incanele rods on the stacks
inside the furnaces I traveled a lot on this job. I did work for Kubota, Electrolux, BMW. There was also plenty
of work for 7018 rods to.

Licensed Pipe Welder
ARKANSAS DEPARTMENT OF HEALTH – Little Rock, AR – 2012 to 2012
Little Rock, Arkansas 2012
Certifies that Ducy James is a duly licensed plumber and pipefitter. I’m a union member of local 55 out of Little
Rock, Arkansas and obtain my Welding craft through MCC mechanical piping for the Union.

ASSISTANT WELDING INSTRUCTOR/PART TIME
Arkansas Northeastern College Burdette – 2008 to 2012
Assist students by demonstrating a thorough and accurate knowledge of the welding field. Prepare welding
materials for daily use and maintains all equipment.

JOURNEYMAN-WELDER/PIPEFITTER, Lexicon
Custom Metals – Jonesboro, AR – 2006 to 2008
Certified AWS-Welder, worked for an industry leader in high quality steel plate fabrications, installation, and
maintenance. Serviced a broad spectrum of industries including the Power and Steel. Diverse capabilities
covering a complete range of products such as plate work, miscellaneous and structural steel, HV/AC systems,
food/chemical grade fabrication.

CLASS A WELDER
Neat Press – Jonesboro, AR – 2004 to 2006
Worked for one of the largest premier, full-line precision sheet metal and structural fabricators. Committed to
producing an on-time quality product. Could take a job from design to completion with quality.

WELDER
American Railcar Industries – Paragould, AR – 2003 to 2004
Worked in repair shop offering the highest level of service in all aspects of railcar and tank repair from major
wreck rebuilding to light repairs on a fast track. Programmed an operated computerized automated welder.
Weather conditions did not prevent quality and efficient welds.

Specialized Training
Blue print Reading for welders, SMAW Structural welding(Partial Joint Penetration);SMAW Structural
Welding(Complete Joint Penetration); Shield Metal Arc Welding(SMAW)Pipe Welding; Tungsten Inert
Gas(Tig)Pipe Welding; Gas Metal Arc Welding; Tungsten Inert Gas (Tig) Manufacturing and Flux Cored Arc
Welding.

EDUCATION

Certificate in Education
Arkansas Northeastern College – Burdette, AR
2009 to 2010

Diploma
Black River Technical College-Paragould – Paragould, AR
2003

Wynne High School – Wynne, AR
1997

ADDITIONAL INFORMATION

Hard worker and team player safety first!