Able to troubleshoot high and low voltage circuits feeding robots, tools conveyors and other devices.
Experienced in troubleshooting testing and repairing 480 volt feeder breakers,13200 volt transformers, and dual switches.
Experienced in maintaining switch houses, substations and other high power distribution houses.
Ability to conduct continuity, resistance and voltage testing.
Skilled in the operation of fabrication shop tools such as lathes, shears, drill presses, extrusion cutters, sanders, table saws and other shop equipment

Associate of General Studies, May 2010
Macomb County Community College - Warren, MI
Associate of Science, December 2010
Wayne County Community College - Detroit, MI

NexTech Professional Services
Comau Pico- Royal Oak, MI/Novi, MI Sept. 2013- Jan. 2015
Machine Tool Electrician
Responsible for terminating and troubleshooting HMI panels and main distribution panels.
Implemented design changes on end effectors, small and large tools.
Performed Input/Output checks on all small tools and end effectors.
Wired and troubleshot test leak panels and station control panels.
Shores Technologies
Machine tool control systems - Grob Systems Inc- Bluffton, OH Nov. 2011- May.2013
Machine tool control systems- Heller Machine Tools- Troy, MI Nov. 2011
Machine Tool Electrician
Terminated nut feeder panels. (480 volts and 24 volts dc)
Terminated press gripper panels ( 120 volts and 24 volts dc)
Corded two identical dunnage conveyors to I/O blocks and asi modules
Supervised the installation of 480 volt ac and 24 volt dc power to various devices such as I/O blocks, robot controllers, nut feeders, and RFID’s
Terminated robot controllers with temp power to teach fanuc robots. (480 volts and 24 volt dc)
Responsible for maintaining the operation of conveyor motors to assist plc programmers.
Ran 24 volt power and communication to asi modules and splitters.
Terminated and troubleshot main panels feeding leak test machines and bearing cap install machines
Responsible for prepping all wires for leak test cells and bearing cap install machines.
Installed cable ducts for high and low voltage wire
Stabbed various bus plugs to feed a CNC machines

Gonzalez Contracting
Martinrea Heavy Stamping- Shelbyville, KY Sept. 2011- Oct.2011
Utica Enterprises- Port Huron, MI Sept. 2011
Machine tool Electrician
Wired light receptacles, weld timers, robot controllers and interface panels
Conducted continuity testing on all weld timers, pedestal welders and robot controllers.
Terminated weld timer panels, interface panels and lighting panels
Installed 24 volt temperature controllers and resolvers on ABB robot end effectors..
Referenced switch layouts to wire multiple I/O blocks for machine tools.
Installed and maintained 120 volt aux cables and 24 volt device net cables to different loads such as turntables, water savers, tip dressers, IP panels, robot controllers, distribution panels and other 120 volt control panels.
Conducted HMI panel troubleshooting for device net issues on different networks.
Installed and troubleshot end effectors on Fanuc Robots.

Solaris Power Service – Troy, MI July 2004- Sept. 2011
Substation Installation and Maintenance Electrician
Conducted an arc flash survey of high voltage power distribution at the Warren Tech Center, Chrysler assembly plant in Sterling Heights, MI and Federal Mogul in Southfield, MI.
Collected conductor sizes, fuse sizes and data plate information from 480V and 120V disconnects, buss ducts and buss plugs, motor control centers, molded case breaker panels, main breakers, feeder breakers, tie breakers and transformers.
Performed tests on feeder breakers, main breakers, tie breakers and transformers of low and high voltages.
Repaired a 13,200 volt switch at the Warren Tech Center.
Serviced DTE Yard at Steel Case in Grand Rapids, MI

Last Resume Update February 5, 2015
Address Lithia Springs
E-mail lock Locked
Phone Number lock Locked
Resume File Galen-Hassel-resume-2015.docx 26.38 kB
Spanish Speaking? No
Willing to Relocate? No

Contact Candidate

Login or purchase this resume contact details.