Objectives:

To pursue a career that enables me to contribute my creativeness, intellect, enthusiasm, professionalism, and to gain life skills and build character in the process.

Education:

I have completed three years of electrical apprentice training through the JATC in conjunction with NECA, IBEW, and Casper College in Casper Wyoming.

High school diploma received through Northwest High School in Cedar Hill Missouri.

Experience:

Berwick Electric- January 2016- June 2016

Phone:xxx-xxx-xxxx

I worked with Berwick in Wheatland,WY, at the Laramie River Station power house upgrading unit two cooling towers and installing a new control systems. This involved planning, layout, and execution of large pipe runs. Building racks, setting panels, pulling wire and termination of devices and fixtures. Also, the planning, layout, and execution of cable tray racks and cable tray. I worked as a team with many fellow electricians, and communication with other trades to set large pieces of gear, and transformers. Then ran pipe to these pieces of equipment , pulled wire, and finally the termination of the equipment. Lastly, as a team, we pulled underground feeders in runs over 2000 feet conjoining all installations to a new power source. I was on site from start to finish of the job and received a clean layoff.

Duties:

Follow the NEC

Read and follow blueprints

Work as a team with co workers to complete the task at hand

Follow instructions as given by Journeyman and or Foreman

Keep work area clean

Keep up with apprentice duties everyday including: unlocking all job trailers every morning, fueling trucks when needed, taking out trash, organizing materials, and clean job trailers once weekly

Keep a detailed list of materials needed

Operate heavy equipment such as boom lifts and forklifts

Set up wire pulls and label conductors

Yellowstone Electric – September 2015 – December 2015

Phone:xxx-xxx-xxxx

I worked with Yellowstone for a short period of time to help them meet a deadline and were short handed. The job site was in Cody,WY at the West Park Hospital remodel. For my duration of employment I installed devices and hung fixtures.

Duties:

Follow the NEC

Read and follow blue prints

Work as team to complete the task at hand

Follow instructions as given by Journeyman and or Forman

Follow the chain of command

Complete apprentice duties

Keep work area clean

Work with customer to complete any requests as not shown on the blue prints

Berwick Electric – March 2015 – September 2015

Phone:xxx-xxx-xxxx

I worked with Berwick at the Jim Bridger power plant in Rock Springs WY to complete the unit two SCR project and also a new ammonia holding building. My job tasks included planning, layout, and execution of large and complex pipe runs. Working as a team and with other trades to set large gear and then to pipe to these pieces of equipment. Pulling wire to and termination of large junction boxes and marshaling cabinets. Following the prints to set devices as shown and termination of these devices. Crafting racks from scratch to hang fixtures. Also, working as a team to pull massive amounts of wire through out the plant all to converge in one large control room.

Duties:

Follow the NEC

Read and follow blue prints

Work as a team to complete the task at hand

Follow instructions as given by Journeyman and or Foreman

Follow the chain of command

Complete apprentice duties

Keep work area clean

Organize parts trailer

Keep job trailers clean

Operate heavy equipment such as forklifts, boom lifts, and scissor lifts

ITC Electrical Technologies – July 2014 – November 2014

Phone:xxx-xxx-xxxx

I worked with ITC in Laramie WY at the University Wyoming campus on the Half Acre Gym and Arena Auditorium projects. During my employment at ITC we were in the rough in stage of these projects, and my duties were as follows: planning, layout, and installation of EMT conduit. Follow prints to set boxes for future devices. Work with, and communicate schedules and plans to make our goals and objectives come together. Pull wire through pipe runs previously installed. Follow the code for all installations.

I had a prior knee injury come back to haunt me and left me unable to work. I left the job on medical leave and received surgery shortly after.

Duties: Follow the NEC

Read and follow blue prints

Work as a team to complete the task at hand

Follow instructions as given by Journeyman and or Foreman

Follow the chain of command

Complete apprentice duties

Keep work area clean

Organize parts trailer weekly

Keep job trailers clean

Electrical Corporation Of America – March 2013 – April 2014

Phone:xxx-xxx-xxxx

I worked with ECA at the Laramie River Station power plant in Wheatland, Wy. I worked on the maintenance crew for the entire duration of my employment. My job details were as follows: replace any equipment that was no longer functioning, including motors, switch gear, instrumentation devices, panel boxes, and light fixtures. This also included installing new installations as provided by the customer. Also working with the on site electrical department to achieve any and all instructions as requested. Which included taking over any projects they could not complete. All installations were up to code.

Duties: Follow the NEC

Read and follow blue prints

Work as a team to complete the task at hand

Follow instructions as given by Journeyman and or Foreman

Follow the chain of command

Complete apprentice duties

Keep work area clean

Organize parts trailer weekly

Operate heavy equipment such as forklifts, boom lifts, and scissor lifts.

Skills:

Knowledge and understanding of the NEC 2014

Ability to learn and adapt quickly

Computer base knowledge

MS office applications

Continuously expanding knowledge of the electrical industry

Continuously expanding knowledge of the construction industry

Planning and layout of pipe runs

Ability to use trigonometry to bend RMC and EMT pipe

Ability to follow and take specific orders

Welding and brazing skills

Ability to follow and take specific orders

Metal skills that involve bending and forming sheet metal

Framing and drywall experience

Local 1310 floor layers union and basic training classes

Member of Local 415 IBEW Cheyenne Wyoming

Working understanding of transformers and motors

Working understanding of DC and AC circuitry

Ability to size and de-rate conductors

Ability to complete calculations as required by the NEC

Basic understanding of PLC’s and constructing control circuits

Very mechanically inclined

Responsible

Punctual

Take pride in my craftsmanship and quality installations

Thirst for knowledge

Conclusion:

I have love for the electrical and construction industry. Being able to unleash my skills and knowledge brings me joy. Please allow me to transform and channel my energy and enthusiasm into an asset for your company. Allow me to help you complete your needs in a professional and diligent manner. All while making work fun and exciting. If you have any further questions please contact mexxx-xxx-xxxx any time during the day as I would be more than happy to assist you further in finding the right match for the job, which I hope is me. Thank you

Page 2 | xxx@xxx.com

Page 3