Install and troubleshoot GSM/UMTS/LTE telecommunications equipment and radios
Repair or replace faulty, damaged, or malfunctioning parts
Test repaired, newly installed, or updated equipment to ensure that it works properly
Adjust or modify equipment to improve its performance
Demonstrate and explain the use of equipment to customers
Knowledgeable and experienced in all phases of communications
Able to create a workable schedule to meet deadlines efficiently
Electrical knowledge, tools and test equipment.
General Dynamics Information Technology 09/2012 – 11/2014
Sr. Technician, Telecom (Civil Crew Foreman)
Civil work is defined as all work relating to ground level, including but not limited to: cabinet sets, conduit work, ice bridge modification or installation, H-Frame installation, power plant installation, ancillary equipment installation, or modification, or removal of existing equipment, platforms, foundations.
Installation and troubleshooting AT&T communications systems and equipment.NetSure™ -48V DC Power System, NetSure™ +24V DC Power System,
FIF Installation & Grounding of 3G/4G RF and DC Equipment
Grounding and Bonding Requirements for Network Facilities
Alcatel-Lucent Long Term Evolution (LTE)
Radio Access Network (RAN)
Alcatel-Lucent 9412 eNodeB Compact Outdoor
DC Surge Protection for RRHs
Modular Rack DCX-48-60-RM • DC6-48-60-RM • DC12-48-60-RM (Raycap)
Installation and troubleshooting Sprint/Samsung telecommunications systems and equipment.Ground Mounted 1900 Remote Radio Head (RRH) Systems
Multi Modal Base System (MMBS) Eltek Indoor and Outdoor Cabinet
MMBS T-type/Texon Indoor and Outdoor Single Cabinet
Smart MBS UADU (T-type/Texon Indoor and Outdoor Dual Cabinet)
Single-Duel Cabinet Conversion for Eltek, as well as T-type/Texon Cabinets
Battery Back Up (BBU) for both Eltek and T-type/Texon Cabinets
Installations Inc. 11/2009-02/2012
(Installer and Manufacturer)
Directed, installed, and maintained bullet resistant glass
Identified problems, diagnosed causes and determined corrective actions.
Learned all aspects of manufacturing bullet resistant glass
Maintained inventory of parts and hardware
Finish Carpentry with full cabinet, countertop, and interior/exterior door building and installation.
Trilogy Communications 01/2006-11/2009
Installed and programmed E911 systems.
Working with servicing and installing SIAD/CAC/ such as
Paragon, Kentrox, Adit, and Axius.
Installation of Trueposistion LMU for phase 2 E911 GPS location.Installed LMR-240,terminations of DC power, Wire wrapping, I
am also able to lace and have full knowledge of telephony
color code. Worked with
Nortel/Ericsson/Siemens BTS. I have worked with Omni and Sectored Cell sites.
I have also worked on T1 terminations and
troubleshooting. Worked indoor and outdoor cell sites
Quad Communications 01/2006-01/2009
(Cable Installation Technician)
Installed and repaired RG6, RG11 CAT/3 CAT/5 CAT/6 communication
lines and equipment for computer system using instruments such as DSAM meters.
Able to use assigned test equipment including but not
limited to signal level meter (SLM), leakage detector, volt
OHM meter, sweep receiver, underground locator and TDR
Reviewed work orders to move, change, install, repair, or
remove data communications equipment, such as modems, cables, and wires.
Measured, cut, and installed wires and cables.
Spliced wires or cables, using hand-tools, appropriate fittings and connectors
Disassembled equipment and inspected and tested wiring to locate and repair problems.
Installed cable television cables and equipment on
customer’s premise, using electrician’s tools and test equipment.
Plastipak Packaging Inc. 05/1998 - 01/1999
(Husky Injection Molding Technician)
Maintain a high quality product. Leak test and drop test when required. Bottle dimensions when required, S-Dimension when required. Weights every hour. Check work orders to insure current neck finish and bottle weight. Maintain bottle weight to given specification. Complete Machine Operator sheets. Machine settings, control charts, scrap, etc. Able to make machine adjustments as required. Prepare for and help do changeovers correctly. Make periodic checks of heat controls, cooling water temperatures, pressures and functioning of extruder and hydraulic pumping units. Performs preventative maintenance on machines and auxiliary equipment as assigned. -Maintains various daily production reports in SAP as required.
Williamsburg Plastics 04/1995 - 08/1995
(Injection Molding Operator)
Extraction and inspection of various products. Removal of excess flash and product flaws. Maintain high quality product as specified by the client. Packaging and shipping of completed work orders as dictated by the shipping list.Service and Education:
U.S. Army (Infantry) 08/1995 - 04/1998
United States Army Infantry Training Brigade Diploma 1995, Joint Readiness Training Center Certificate of Meritorious Achievement 1996, Expert Infantryman Badge 1996, Expeditionary Medal 1997, Certificate of Achievement for meritorious service during Operation Desert Eagle 1997, Certificate of Training "Combat Life Saver Course" 1997, Certificate of Achievement "Operation Desert Falcon 1997.
Discharged U.S. Army 1998.
Maintain a Safe Working Environment.
Ensure all employees uphold all safety standards, helping to maintain a 100% accident free work place.
Meet and exceed company standards for production.
Through proper planning of time and resources minimize downtime and optimize production.
Ensure proper training of myself and crew members.
Stay current and up to date on training for proper installation of assigned projects.
Keep my crew members up to date on current standards and procedures to produce quality workmanship.
Personal and Professional advancement within my field.
|Last Resume Update||December 8, 2014|
|Resume File|| Jeremy-Resume-Final.docx 21.71 kB|
|Willing to Relocate?||No|